Easy, Adjustable Crib Skirt Tutorial

image_7 - Version 2

So, as you can see, I’ve been having fun with this Studio E “Around Town” fabric!  So far I’ve made nursery art, a mobile, a window cornice box, and now a crib skirt!

There are tons of tutorials about how to make crib skirts however, I found most of them to be a one size only tutorial which didn’t make sense to me!  With a crib, as the baby grows, the mattress height changes which means the crib skirt length changes.  If you only have one length of crib skirt, then what do you do when you have to lower the mattress?  Let it drag on the floor?  With this tutorial, I’d like to show you how I made an adjustable crib skirt that can be used for all 3 mattress heights.

First, let’s take a look at a crib.  Below is a birds eye view of a crib without a mattress in it.  See the space in-between the crib bars and the base?  That’s where you’re crib skirt will hang.

image

To show you the finished birds eye view, I made 3 crib skirt panels (I didn’t make one for the back of the crib because you can’t see it.)  I attached it to the base of the crib with thumb tacks.  I know…it’s not the most polished of finishes but once the mattress is on top, no one will see it!  It’s actually quite neat and tidy!

image_2

So, to make the crib skirt, all you need to do is decide what fabric you’d like to use for your panels, measure your panels out so they fit on each side of the crib, hem them how you wish, slide them in-between the bars and the base of the crib and secure them at the desired length with pins.

If you get the idea, go ahead and make your crib skirt panels how you wish!  If you’d like to see how I did mine specifically, keep reading!

Adjustable Crib Skirt Tutorial:

This tutorial will demonstrate how the side panel was made.

If using “directional fabric,” make sure each panel has the same part of the pattern on it.  For the widest panel, you may need to join the patterned fabric together.   (To learn more about how to join patterned fabric, see a previous tutorial here.)

To make sure each panel has the same section of the pattern on it, cut each patterned strip at the same place.  With this fabric specifically, I chose to cut below the red houses as the top cut and below the red roofs as the bottom cut (as shown.) image

image_1

The side panel needed to be 26″ wide so I cut the patterned strip to be 26″ wide.

image

Then I cut a 26″ wide piece of white fabric and kept it how it comes off the bolt (folded in half.)  I wanted to have 2 layers of white fabric for weight and to make the skirt more opaque.

image_1

Cut off the selvage edge.

image_2

Pin the 26″ raw edge of the patterned fabric, right sides together, to one of the 26″ raw edges of the white fabric.  Sew with a 1/4″ seam.

image_3

Press seam allowance towards the patterned fabric.

image_4

With right sides together again, pin the other 26″ raw edge of the patterned fabric to the other 26″ raw edge of the white fabric and sew together with a 1/4″ seam.  Now you have a large tube of fabric.  Again, press the seam allowance towards the patterned fabric.

image

Now sew up each side of the panel with a 1/4″ seam allowance leaving about a 4″ opening on one side.

image_3

Turn right side out through the 4″ opening you left and press flat.

image_4

Top stitch with a 1/4″ seam allowance over the bottom edge of the panel.

image

Top stitch over the top edge of the pattern piece…

image_1

Finally, top stitch along each side of the panel (not shown).  Make sure you top stitch over the opening you left to turn the panel right side out.  This will neatly close the opening.

Hang your panel in-between the crib bars and the base of the crib and pin to desired height with thumb tacks.

image_4

Repeat with the other 2 sides of the crib.

There you have it – a simple, adjustable, crib skirt.

image_4

Let me know if you give it a try or if you have any suggestions or questions!

Thanks for stopping by and happy sewing!

-AFriendLikeBen-

Advertisements

DIY Hand Stamped Thankyou Cards

watermarked card stamp

These thankyou cards were so fun and easy to make that there is no need for an in-depth explanation!  I made them to compliment my rustic “Cute As A Button” themed baby shower that my family so generously threw for me. To do the same, here’s what you need (plus whatever card you choose to stamp on.)  I purchased all of these materials at Michaels.

image

All you do is stamp one layer at a time!  At the end, I glued a little button on with a some hot glue.

If you’d like to have a closer look at what stamps I used from the packages, I also included the same steps as above while displaying the stamps that I used.

And there you have it!  I loved making these!  I hope my dear friends and family like them! If you’d like to see another sample of simple handmade cards, check out my previous post “Christmas Card Creations.”

Thanks for stopping by and happy crafting!

-AFriendLikeBen-